MAPP/EAA处理对聚丙烯/小麦秸秆粉复合材料性能的影响

研究了马来酸酐接枝聚丙烯（MAPP）、乙烯丙烯酸共聚物（EAA）处理对聚丙烯（PP） /小麦秸秆粉（WSP）复合材料性能的影响。结果表明，随着体系中MAPP质量份数的增加，PP/WSP的拉伸强度和弯曲强度均逐渐增大，但冲击强度却先增加后减小，复合材料达到塑化峰的时间逐渐延长；使用EAA后，无论体系中是否已经使用了MAPP，PP/WSP的拉伸、弯曲和冲击强度均可得以提高，特别对于未使用MAPP的体系，效果更加明显，可分别提高65.04 %、45.42 %和6.75 %，储能模量增加，表面疏水性增强，平衡扭矩从13.9 N·m降至11.8 N·m，吸水尺寸变化率及吸水率下降，吸水平衡时间缩短；使用EAA可改善PP/WSP中WSP与PP间的界面结合，改善PP/WSP力学性能、热稳定性能、表面疏水性能、尺寸稳定性能和加工性能，降低其吸水率。     

40万t/年转炉钢渣蒸汽陈化处理生产线

介绍了针对国内某炼钢厂专门设计的40万t/年转炉钢渣蒸汽陈化处理生产线主要参数及工艺流程,对该生产线中的钢渣倾翻车、钢渣冷却搅碎车、转运车、蒸汽陈化釜等主要设备特点进行了阐述,同时对该生产线应用的冷却水量研究、搅碎辊轨迹优化等关键技术作了进一步的探讨。     

掺杂EBS润滑剂的粉末冶金铝合金脱脂工艺研究

文章通过冷压-烧结制备了掺杂EBS润滑剂的粉末冶金铝合金,比较了单/多温段脱脂工艺优劣,发现多温段脱脂优于单温段脱脂,脱脂更彻底,但由于气体流量不能无限大,导致气氛脱脂得到的样品碳含量无法达到碳剩余理论值0.02%。研究了真空脱脂和空气负压脱脂机制,真空脱脂可使得EBS热分解的气态有机物和灰分从压坯表面逸出,并被及时带出炉外,最终合金碳含量接近碳剩余理论值0.02%；空气负压脱脂可使得残余碳被氧化逸出,脱碳更彻底,使样品碳含量低于碳剩余理论值。研究了脱脂工艺对合金力学性能的影响,真空脱脂合金力学性能优于气氛脱脂,相对密度最大为97.86%,拉伸强度最大为218.06MPa,接近未添加润滑剂合金的力学性能；空气负压脱脂虽然可使碳含量更低,但因脱脂过程中样品暴露在空气中,使得原料粉末也被氧化,导致最终的合金力学性能严重下降。     

高压料床挤压对钢渣易磨性改善的应用研究

在分析了大量钢渣原料的化学成分、矿物组成和粉磨邦德功指数基础上，依据辊压机高压料床挤压粉碎原理，本文采用辊压机对钢渣进行预挤压试验，并参照相对易磨性试验方法，对比了挤压前后钢渣粉磨特性的变化，试验结果表明辊压机高压料床的挤压粉碎作用大大改善了钢渣的易磨性，有效的降低了钢渣的粉磨电耗。     

酸性废水中As(Ⅲ)、Cu(Ⅱ)与铁粉的反应行为

在Fe-As(Ⅲ)-Cu(Ⅱ)-H₂O体系中, 研究了酸性废水中As(Ⅲ)、Cu(Ⅱ)与金属铁粉的反应行为, 考察了反应过程中As在气、液、固三相中的分配比。结果表明, As(Ⅲ)和Cu(Ⅱ)离子被Fe还原为单质As和Cu后, As、Cu进一步结合成Cu₅As₂等金属间化合物, 从而促进As(Ⅲ)沉淀反应的发生, 且无AsH3生成。在反应时间40min、铁粉过量系数1.2、溶液初始pH=0.0、温度40 ℃、Cu/As摩尔比1.0条件下, As在气、液、固三相中的分配比分别为0、20.7%和79.3%, 沉砷率为79.3%。     

粉末注射成型技术的研究和应用

介绍了粉末注射成型技术的概念和工艺,包括金属粉末注射成型(MIM)、陶瓷粉末注射成型(CIM),讲述了黏结剂的使用发展情况;阐述了粉末注射成型专用注射成型机的特点,PIM粉末注射专用塑化系统,PIM专用料斗滑块装置,镶套式机筒座等,介绍了PIM技术在诸多行业中的应用,3C行业,医疗行业,汽车行业等,并展望了PIM研究的发展方向。     

Corrosion resistance of Al–Cr-slag containing chromium–corundum refractories to slags with different basicity

Al–Cr slag is the solid waste generated by the smelting of Cr metal. It presents a range of environmental hazards. This study addressed the corrosion resistance of Al–Cr slag containing chromium–corundum refractories to slags with different basicity. Herein, we provide suggestions for the use of Cr–corundum of different basicity in kilns. Al–Cr slag, brown fused Al₂O₃, and chrome green were used as the raw materials, with pure calcium aluminate cement being used as a binder. The brick samples, prepared using different blends of chrome green and corundum, were fired at 1600?°C, and subsequently subjected to a slag corrosion test. After corrosion by slag of different basicity, the phase composition and microstructure of the sample were analyzed by X-ray diffraction, energy dispersive spectrometer and scanning electron microscopy. There were two major findings. First, Cr–corundum brick made from Al–Cr slag has a better slag corrosion resistance than that made from Cr₂O₃ and brown fused Al₂O₃. Second, Cr–corundum brick made from Al–Cr slag has superior corrosion resistance to slag with a CaO:SiO₂ ratio of 2:1.     

Synergistic effect of glass fibre and Al powder on the mechanical properties of glass-ceramics

To explore the synergistic effect of glass fibre and Al powder on the mechanical properties of glass-ceramics, blast furnace slag was chosen as the main material, and glass fibre and Al powder as reinforcement materials. The phase compositions, microstructures, compressive properties, and apparent density of the glass-ceramics with varying quantities of glass fibre and Al powder were investigated. The experimental results indicated that Al powder could exist as a simple substance in glass-ceramics and form a dense net coating on the surface of blast furnace slag to improve the plasticity of the glass-ceramic. The glass fibre had better reinforcement effect than Al powder because of its extremely high mechanical strength. The plasticity of glass-ceramics, however, severely decreased; the glass-ceramics exhibited brittle failure during compression. A slight increase in the content of CaSi₂ and SiO₂ in the glass-ceramics was closely related to the addition of glass fibre. Considering safety and economy, glass-ceramics with 6% Al and 14% glass fibre (S4) have the best mechanical properties. The compressive strength, strain at maximum force, and apparent density were 40?MPa, 19% and 1.974?g/cm³, respectively.     

Study on the relationship between the particle size distribution and the effectiveness of the K‐powder fire extinguishing agent

The relationship between the particle size distribution and the extinguishing effectiveness of the new K‐powder fire extinguishing agent has been studied experimentally, to explore the reason of the great extinguishing efficiency exhibited by the new K‐powder fire extinguishing agent on Class B fire (liquid fuel fire). The results of the experiment showed that the extinguishing effectiveness increased along with the decrease of the particle size distribution. In addition, a sharp discontinuity appeared around the limiting size, about 40 μm. The powder with the particle size below 40 μm exhibited highly effective extinguishing with the minimum effective extinguishing concentration C_xr = 23 g·m^?3, while the powder with the particle size above 40 μm exhibited little fire extinguishing efficiency. Compared with other fire extinguishing agents produced by different substances, the new K‐powder fire extinguishing has the bigger limiting size. That means, in the same particle size distribution, the new K‐powder fire extinguishing agent contains more highly effective powder than others contain, and is more effective.